| |
 |
| |
| Mitsubishi Color Paper accurately
reproduces color tones with sharp highlights. |
| |
 SA-H
Speed Access Paper |
| Only Mitsubishi's advanced emulsion
technology brings you the next generation of rapid access color paper. |
| |
 |
- Outstanding sharpness
- True color reproduction
- Pure whites
- Neutral tone gradation
- Extremely high resistance to scratches, pressure marks and static
- Excellent image stability
- Fully compatible with Mitsubishi SA, RA-4 or equivalent chemistries
|
| |
SPECTRAL SENSITIVITY |
| SA-H's specially arranged R/G/B sensitivity
works with all commonly used light sources of modern automatic printers and printing
equipment. |
|
CHARACTERISTIC CURVES |
| Well-balanced neutral tone gradation
from deep shadows to highlights assures excellent color reproduction. The wider
exposure latitude contributes to the higher output of salable prints, especially
when automated high-speed production methods are used. |
|
RECIPROCITY CHARACTERISTICS |
| Excellent reciprocity characteristics
allow a neutral balance to be maintained over a wide range of exposures, thus
eliminating the need for color corrections with varying exposure times. |
|
LATENT IMAGE STABILITY |
| The excellent latent image characteristics
of SAH paper afford the user wide flexibility in the time between printing and
processing. |
|
STORAGE OF RAW STOCKS |
| Avoid high temperature and humidity.
Raw stocks should be kept in cold storage(store below 10°C(50°F)and low
relative humidity (50%-70%). Warm up to room temperature before usingto prevent
moisture condensation. Warm-up time from 10°to 20°C (50°to 60°F)is
3 to 5 hours. |
|
SAFELIGHT |
| Mitsubishi Color Paper SAH should
be handled in total darkness. If necessary,a 7 1/2W tungsten bulb with Kodak Safelight
Filter No. 13 or equivalent may be used at a distance from paper surface of at
least 1m (3.3 ft.). However,safelight exposure time should be kept to a minimum. |
|
PROCESSING CHEMISTRY |
| Mitsubishi SAH Chemistry, RA-4 or
equivalents. |
|
| |
 |
| |
| AVAILABLE SURFACES |
| Glossy |
F |
Type SA-H220
|
| Luster |
E |
Type SA-H810 |
|
| |
|
| |
| STANDARD PROCESSING STEPS |
| Processing Step |
Temperature |
Time
|
| Color Developer |
35.0°+ 0.3°C (95+0.5°F) |
45 seconds |
| Bleach-Fix |
30° to 36°C (86° to 97°F) |
45 seconds
|
| Total Control Stabilizer |
30° to 37°C (86° to 99°F) |
90 seconds |
| Dry |
50° to 70°C
(122° to 158°F) |
. |
|
| |
|
| |
| AVAILABLE SIZES |
Length
|
83.8m(275ft.) |
175.3m(575ft.) |
236.2m(775ft.) |
350.5m(1150ft.) |
| Width |
|
|
|
|
| 8.9cm (3 1/2in.) |
. |
O |
O |
O |
| 10.2cm (4in.) |
. |
O |
O |
O |
| 12.7cm (5in.) |
. |
O |
O |
. |
| 15.2cm (6in.) |
. |
O |
. |
. |
| 20.3cm (8in.) |
O |
O |
. |
. |
| 25.4cm (10in.) |
O |
O |
. |
. |
| 27.9cm (11in.) |
O |
. |
. |
. |
|
| |
